What the Obwegeser osteotome for the alveolar process is
The Obwegeser osteotome for the alveolar process cuts the bone between and around the teeth. When a segment of the jaw that carries a group of teeth is moved on its own, or a narrow ridge is split to widen it, the cuts run through the alveolar bone close to the roots. A narrow blade with a ridged handle gives the control that work needs, a little at a time under light blows.
Google AI Mode, read on 4 November 2026, calls it the Obwegeser alveolar process osteotome, a maxillofacial instrument designed to divide and work the bones of the alveolar process. It places it in oral, maxillofacial, ENT and plastic surgery, with a blade beveled on both sides and a ridged or flat handle that does not slip.
Gemini, read the same day, places it in oral and maxillofacial surgery, periodontics and dental implant work, on the alveolar process, the bone between the teeth and the ridges of the upper jaw. It lists the alveolar ridge osteotome and the obwegeser osteotome for alveolar process 3mm 4mm 6.5mm as catalog names. Buyers who do not know the name type ridge split osteotome.
Key design features
A narrow blade
Our photograph shows a narrow blade at the tip of a slim shaft, and the drawings beside it show the blade from the front and the side, tapering to its edge. A narrow blade fits between the roots of the teeth, where a broad one would touch them.
A ridged handle
The handle in our photograph is slim and ridged. Alveolar work is done with light, measured blows, and the ridges hold the fingers steady between them. AI Mode describes a ridged handle of the same kind for this pattern.
Three widths
The listing sells 3, 4 and 6.5 mm, all at 20 dollars. The 3 mm works between two roots that sit close together. The 6.5 mm splits a ridge along its crest. The 4 mm sits between them, for cuts round a single tooth. A segmental tray can carry the three in order, so the width changes as the cut moves from between the roots to the crest.
Two Obwegeser alveolar listings
Our site carries two Obwegeser alveolar osteotomes on two item codes. This one, ADM-684.03, has a ridged handle and comes in 3, 4 and 6.5 mm. The Obwegeser alveolar osteotome on ADM-620.02 is a one piece ridged shaft in 2, 4 and 6.5 mm.
Which width to order
Three widths at one price, read off the variations on 4 November 2026. The guide below is ours. The listing gives no length.
| Width | Suits, our guide | Price |
|---|---|---|
| 3 mm | Between two roots that sit close together | 20 dollars |
| 4 mm | Cuts round a single tooth | 20 dollars |
| 6.5 mm | Splitting a ridge along its crest | 20 dollars |
Where it is used
AI Mode and Gemini, read on 4 November 2026, name these cases for the Obwegeser osteotome for the alveolar process.
| Case | What it cuts | Why this one |
|---|---|---|
| Segmental jaw surgery | Alveolar bone between the teeth | The narrow blade fits between roots |
| Ridge splitting | The crest of a narrow ridge | The 6.5 mm runs along it |
| Periodontics and implant work | The ridges of the upper jaw | Gemini names them |
| ENT and plastic surgery | Bone of the alveolar process | Named by AI Mode |
What it does, and what it must not do
The Obwegeser osteotome for the alveolar process makes fine cuts in the bone round the teeth. It is not for the thick bone of the ramus and not a lever.
| Job | Use this alveolar osteotome? | What to use instead or beside it |
|---|---|---|
| Fine cuts in the alveolar bone | Yes | This is the job it is made for |
| A 2 mm cut on a one piece shaft | Beside it | The Obwegeser alveolar osteotome, ADM-620.02 |
| Splitting the ramus | No | The Hargis osteotome |
| Long straight cuts across the jaw | No | The Obwegeser blade osteotome |
| Levering a tooth or a segment | Never | Nothing; the blade is not a lever |
How it compares with the rest of the osteotomes
Eleven maxillofacial osteotomes make up this family on our site. The working ends and handles are read off each listing’s own photograph, the options off the variations and the prices off the order form, on 4 November 2026. No listing gives a length, so none is printed.
| Osteotome | Working end, from our photograph | Handle, from our photograph | Options on the listing | Price |
|---|---|---|---|---|
| Dautrey-Munro | broad flat blade running the full length of a one piece bar | the bar itself, to a small flared striking end | 4, 6, 8, 10, 12, 14 or 16 mm | 22 dollars |
| Epker | long slim blade; drawings of straight, slightly and strongly curved tips | knurled lower grip, round flared striking end | 4, 6 or 8 mm by 1.2 mm, three curves | 20 dollars |
| Hargis | short, broad flat blade on a narrow neck | dark textured handle | 10 or 20 mm | 36 dollars |
| Obwegeser blade | flat blade on a narrow neck; drawings of four widths | brown handle with a metal end cap | 8, 12, 16 or 20 mm | 36 dollars |
| Obwegeser wedge | narrow flat blade on a neck; a thin tapered wedge in the drawing | brown handle with a metal end cap | 7 or 10 mm | 37 dollars |
| Obwegeser maxillary | one piece flat bar curving toward its tip | the bar itself, to a flared striking end | 8 or 11 mm | 28 dollars |
| Obwegeser nasal septum | forked tip, two prongs ending in small round knobs | long slim shaft to a square striking block | 4 or 6 mm | 33 dollars |
| Obwegeser alveolar process (this page) | narrow blade at the tip of a slim shaft | ridged handle | 3, 4 or 6.5 mm | 20 dollars |
| Obwegeser alveolar, one piece | very narrow blade on a slim one piece shaft | the shaft, ridged along its length | 2, 4 or 6.5 mm | 19 dollars |
| Marchac | slim straight blade; drawings of three widths | ridged handle with a round striking cap | 4, 6 or 8 mm, straight or curved | 23 dollars |
| Tessier graft calva | broad flat blade; square shoulders in the drawing | faceted shaft to a round flared striking plate | 10 or 15 mm, straight or curved | 33 dollars |
Materials and finish
Every Obwegeser osteotome for the alveolar process we make is formed from high quality medical grade stainless steel. The steel itself is made to a German specification. We do not publish a grade number.
The Obwegeser osteotome has a plain steel finish. Look along the narrow edge before each case. A chipped edge on a 3 mm blade wanders in the bone, and that osteotome should be set aside.
Caring for it
Rinse the Obwegeser osteotome as soon as the case ends, before blood and bone dust dry on the blade and in the ridges of the handle. Brush both, wash it, dry it, and steam sterilize it on the normal cycle. Keep the three widths in order on the tray.
Ordering and wholesale
The Obwegeser osteotome for the alveolar process is made by Adas Instruments in our own workshop and sold direct, which is why the price sits where it does against the catalog houses. Order one for a single tray, or in quantity for a hospital list or a distributor line. We do OEM work under your own brand and your own item numbers. Send us a sample and we will hold a run to your pattern rather than ours. Stock items ship from our own workshop. Backorder items take 10 to 12 working days to make. Every instrument carries a three year replacement warranty against manufacturing defects. Production is controlled under an ISO 13485 quality management system.
Frequently asked questions
What is the Obwegeser osteotome for the alveolar process used for?
It divides and works the bone of the alveolar process, the ridge that holds the teeth, in oral, maxillofacial, ENT and plastic surgery. Gemini adds periodontics and implant work. Ours is 3, 4 or 6.5 mm, at 20 dollars.
What is an osteotome used for?
An osteotome cuts bone. Its edge is set on the bone and the end is tapped with a mallet, so the cut goes where it is aimed. On the jaws, osteotomes divide bone so that a jaw, or a segment of it, can be moved and fixed in a new place.
Which alveolar process width should I order?
The 3 mm works between roots that sit close together, and the 4 mm round a single tooth. The 6.5 mm splits a ridge along its crest. All three are 20 dollars, and a segmental tray can carry them in order.
How is the alveolar process osteotome different from the other one?
Our site carries two. This one, ADM-684.03, has a ridged handle in 3, 4 and 6.5 mm at 20 dollars. The other, ADM-620.02, is a one piece ridged shaft in 2, 4 and 6.5 mm at 19 dollars. Pick the one whose handle and smallest width suit your hand and the bone.
Can it be autoclaved?
Yes. It is stainless steel with no coating, and it goes through the normal steam cycle with the rest of the tray. Brush the ridges of the handle clean, dry it fully, and store it so the narrow edge is protected.
Related products and categories
Three more osteotomes from the same maxillofacial tray: the Obwegeser alveolar osteotome, one piece, the Marchac osteotome and the Tessier graft calva osteotome. The rest of the range is under maxillofacial instruments, which sits inside our ENT instruments.


Reviews
There are no reviews yet.