What an Obwegeser third molar retractor is
An impacted lower wisdom tooth sits behind the last molar, low in the bone, with the flap, the cheek and the tongue all pressing toward the site. The surgeon needs the flap held off the bone while the bur works, and a flat cheek retractor does not reach that far or hold that edge. The third molar retractor is made for that one place in the mouth.
Google AI Mode, read on 3 November 2026, describes the Obwegeser third molar retractor, which it also calls an Obwegeser wisdom tooth retractor, as a hand held instrument for oral, maxillofacial and dental surgery. It is made for access and sight during the extraction of impacted third molars and surgery on the mandibular ramus. It describes an L shaped blade whose tip fits against the alveolar bone and holds the gum and the flap without slipping.
Gemini, read the same day, gives the Obwegeser molar flap retractor as another catalog name. Buyers who simply ask for a third molar retractor or a wisdom tooth retractor are asking for this pattern, a long right angled blade that reaches past the second molar.
Key design features
A blade at a right angle
In our photograph the blade is flat and turned at a right angle to a slim shaft. The shaft runs forward along the cheek, and the blade drops down behind the last molar. That angle lets the assistant hold the flap from the front of the mouth, with the hand outside the lips.
A turned down tip
The tip of the blade turns down into a short lip. The lip catches under the edge of the flap or against the bone, so the blade holds where it is placed instead of sliding along wet tissue. The AI Mode answer names the same idea: an edge that fits against the alveolar bone without slipping.
Twenty four centimeters of reach
At 24 cm the retractor is long enough to reach the back of the lower jaw from the corner of the mouth. The extra length keeps the assistant’s hand clear of the bur, the suction and the surgeon’s line of sight, which is the reason to choose a long instrument for this work.
A ring and a loop for the hand
The shaft carries a ring above an open loop handle. A finger through the ring gives a light hold for short steps, and the loop takes the whole hand for the long pull while bone is removed. The open handle also weighs less than a solid one over a long case.
Which one to order
The listing carries one size, read on 3 November 2026. Order one per wisdom tooth tray, and a second if two cases run back to back.
| What you get | Length | Working end | Price |
|---|---|---|---|
| Obwegeser third molar retractor | 24 cm | Right angled blade, tip turned down | 26 dollars |
| Spare for a second tray | 24 cm | The same | 26 dollars |
Where it is used
Gemini, read on 3 November 2026, places it in oral and maxillofacial surgery, pediatric oral surgery and implant work, on the pad behind the last molar, the soft tissue round the angle of the jaw and the flaps over impacted lower third molars.
| Case | What it holds | Why this shape |
|---|---|---|
| Impacted lower wisdom tooth | The flap and the cheek behind the last molar | The right angle reaches past the second molar |
| Bone removal round the tooth | The flap off the bone | The turned down tip catches the flap edge |
| Surgery on the front of the ramus | Soft tissue over the ramus | Long reach from the front of the mouth |
| Implant at the back of the lower jaw | Flap and cheek | The hand stays out of the field |
What it holds back, and what it must not do
It holds soft tissue at the back of the jaw. It is not a lever and it does not open the mouth.
| Job | Use the third molar retractor? | What to use instead or beside it |
|---|---|---|
| Holding the flap at a lower wisdom tooth | Yes | This is the job it is made for |
| Holding the cheek at the front of the mouth | Larger than needed | A cheek retractor such as the Cawood-Minnesota |
| Holding the posterior border of the ramus | No | An Obwegeser ramus retractor |
| Keeping the mouth open | No | A mouth gag or a bite block |
| Levering a tooth out | Never | An elevator; the blade bends under that load |
How it compares with the rest of the family
Ten Obwegeser and Munro jaw retractors make up this family on our site. The working ends are read off each listing’s own photograph, the sizes off the variations, the lengths off the name and the prices off the order form, on 3 November 2026.
| Retractor | Working end, from our photograph | Sizes on the listing | Length | Price |
|---|---|---|---|---|
| Obwegeser third molar (this page) | right angled blade with a turned down tip, ring and loop handle | one size | 24 cm | 26 dollars |
| Obwegeser retractor 24 cm | right angled blade, bent up or bent down, ring and loop handle | seven blades, 5 x 16 to 16 x 80 mm | 24 cm | 26 dollars |
| Obwegeser soft tissue 21 cm | wider right angled blade, ring and loop handle | three blades, 11 x 40 to 16 x 80 mm | 21 cm | 26 dollars |
| Obwegeser ramus 24 cm | right angled blade with a notched tip, ring and loop handle | 11/15 x 70 or 12/22 x 70 mm | 24 cm | 26 dollars |
| Obwegeser ramus 22 cm | right angled blade with a notched tip, ring and loop handle | one size | 22 cm | 26 dollars |
| Obwegeser nasal spine 22 cm | narrow right angled blade, ring and loop handle | one size | 22 cm | 24 dollars |
| Obwegeser nasal spine 24 cm | right angled blade with a forked tip, ring and loop handle | one size | 24 cm | 24 dollars |
| Obwegeser chin | flat angled bar with a pronged tip | one size | 16 cm | 20 dollars |
| Obwegeser channel | flat bar, slim rounded end and a curved channel hook | 8 or 10 mm | 16 cm | 14 dollars |
| Munro ramus | broad curved blade on a solid hooked handle | four blades, 20 to 35 x 80 mm | 16 cm | 28 dollars |
Materials and finish
Every Obwegeser third molar retractor we make is formed from high quality medical grade stainless steel. The steel itself is made to a German specification. We do not publish a grade number.
The finish is plain steel. Blade, shaft, ring and handle are one piece, so there is no joint at the bend where the blade meets the shaft. Look at the turned tip before each case: a tip that has been flattened will not hold the flap.
Caring for it
Rinse it as soon as the case ends, before blood and bone dust dry under the turned tip. Brush both faces of the blade, the inside of the bend and the inside of the loop handle. Dry it, steam sterilize it on the normal instrument cycle, and look at the angle and the tip before it goes back on the tray. Set aside one whose blade has been opened or whose tip has been bent, rather than bend it back by hand.
Ordering and wholesale
The Obwegeser third molar retractor is made by Adas Instruments in our own workshop and sold direct, which is why the price sits where it does against the catalog houses. Order one for a single tray, or in quantity for a hospital list or a distributor line. We do OEM work under your own brand and your own item numbers. Send us a sample and we will hold a run to your pattern rather than ours. Stock items ship from our own workshop. Backorder items take 10 to 12 working days to make. Every instrument carries a three year replacement warranty against manufacturing defects. Production is controlled under an ISO 13485 quality management system.
Frequently asked questions
What is an Obwegeser third molar retractor used for?
It holds the flap, the cheek and the tongue clear of an impacted lower wisdom tooth while bone is removed and the tooth is taken out. It is also used for surgery on the front of the ramus and for implants at the back of the lower jaw, where a long right angled blade is needed.
Is the third molar retractor the same as a wisdom tooth retractor?
Yes. Google AI Mode gives the Obwegeser wisdom tooth retractor as another name for it, and Gemini adds the Obwegeser molar flap retractor. The names point to the same thing: a long retractor with a right angled blade for the back of the lower jaw.
How long is the Obwegeser third molar retractor?
Ours is 24 cm, which is in the name. That length reaches from the corner of the mouth to the back of the lower jaw while keeping the assistant’s hand out of the way. The listing carries one size at 26 dollars.
How is it different from a Cawood-Minnesota retractor?
Gemini, read on 3 November 2026, puts the difference in the tip. The third molar retractor has a narrow curved tip that hooks behind the last molar, while the Cawood-Minnesota has a broad offset blade for the cheek and flap in general. Ours is listed in our cheek and lip retractor family.
How do I clean the third molar retractor?
Rinse it straight after the case, then brush both faces of the blade, the inside of the bend and the turned tip, where bone dust collects. Dry it and steam sterilize it on the normal cycle. Look at the tip under a light before it goes back on the tray.
Related products and categories
Three more jaw retractors from the same family: the Obwegeser retractor, 24 cm, the Obwegeser soft tissue retractor, 21 cm and the Obwegeser ramus retractor, 24 cm. The rest of the range is under maxillofacial instruments, which sits inside our ENT instruments.



Reviews
There are no reviews yet.