What an Obwegeser retractor is
Jaw surgery done through the mouth needs the soft tissue held off the bone along a long incision, from the front of the jaw back to the ramus. One width of blade does not fit all of it. The obwegeser soft tissue retractor 24cm is sold the way surgeons choose it: by the size of the blade and by which way the tip turns.
Google AI Mode, read on 3 November 2026, calls the Obwegeser retractor a specialized surgical tool for oral and maxillofacial surgery and for plastic and reconstructive work. It holds back soft tissue, lips, cheeks and muscle for a clear view of the mandible and the maxilla. It describes tips curved downward, toe down, or upward, toe up, to hook under flaps or round bone borders, and handles with a finger loop. Our listing offers each blade both ways.
Catalogs sell it the same way, by blade size and by curve, so a buyer orders an obwegeser retractor curved down or an obwegeser retractor curved up. Gemini lists the 24 cm version in oral and maxillofacial, plastic and orthognathic surgery. The obwegeser retractor uses below follow the cases it names.
Key design features
Seven blade sizes
The smallest blade is 5 x 16 mm and the largest 16 x 80 mm, with 7 x 25, 10 x 35, 10 x 42, 12 x 55 and 14 x 70 mm between them. The drawing on our photograph shows all seven. Small blades suit the front of the jaw and a narrow incision; the long ones reach the back of the jaw and hold a deep flap.
Bent up or bent down
Every blade comes with its tip bent upwards or bent downwards. The AI Mode answer puts the difference this way: a tip curved down gives a broader view and a firmer hold, and a tip curved up is gentler on the tissue it holds. A tray can carry both versions of the sizes it uses.
A right angled blade
The blade is turned at a right angle to the shaft, so the shaft runs along the cheek while the blade drops into the incision. The assistant holds from outside the mouth and pulls the tissue toward the lips, which keeps the hand low and out of the light.
A ring and a loop
A ring sits on the shaft above an open loop handle. One finger through the ring gives a light hold for a short step, and the loop takes the whole hand for a long one. At 24 cm the handle stays well clear of the face.
Which blade to order
The fourteen variations on the listing, read on 3 November 2026: seven blades, each bent up or bent down. Every one costs the same.
| Blade on the listing | Tip | Where it suits | Price |
|---|---|---|---|
| 5 x 16 mm | Bent up or bent down | A narrow incision at the front of the jaw | 26 dollars |
| 7 x 25 mm | Bent up or bent down | The front of the jaw and the chin | 26 dollars |
| 10 x 35 mm | Bent up or bent down | The premolar area | 26 dollars |
| 10 x 42 mm | Bent up or bent down | The premolar and molar area | 26 dollars |
| 12 x 55 mm | Bent up or bent down | The molar area and the body of the jaw | 26 dollars |
| 14 x 70 mm | Bent up or bent down | The back of the jaw | 26 dollars |
| 16 x 80 mm | Bent up or bent down | The ramus and a deep flap | 26 dollars |
Where it is used
Gemini, read on 3 November 2026, places the 24 cm Obwegeser in oral and maxillofacial, plastic and reconstructive and orthognathic surgery, on broad facial flaps, the mucosa of the vestibule, the lip and the soft tissue over the masseter.
| Case | What it holds | Blade to start with |
|---|---|---|
| Sagittal split of the lower jaw | Cheek and flap over the body and ramus | 12 x 55 to 16 x 80 mm |
| Le Fort osteotomy of the upper jaw | Lip and cheek over the maxilla | 10 x 35 to 14 x 70 mm |
| Genioplasty | Lip and soft tissue over the chin | 5 x 16 to 10 x 35 mm |
| Plating a jaw fracture | Flap over the fracture line | By the site |
What it holds back, and what it must not do
It holds soft tissue off the bone. It is not a lever, and it does not take the place of a ramus or a channel retractor.
| Job | Use the Obwegeser retractor? | What to use instead or beside it |
|---|---|---|
| Holding cheek, lip and flap along the jaw | Yes | This is the job it is made for |
| Hooking the posterior border of the ramus | No | An Obwegeser ramus retractor |
| Sitting on the lower border during a split | No | An Obwegeser channel retractor |
| Keeping the mouth open | No | A mouth gag or a bite block |
| Levering bone | Never | An elevator; the blade bends under that load |
How it compares with the rest of the family
Ten Obwegeser and Munro jaw retractors make up this family on our site. The working ends are read off each listing’s own photograph, the sizes off the variations, the lengths off the name and the prices off the order form, on 3 November 2026.
| Retractor | Working end, from our photograph | Sizes on the listing | Length | Price |
|---|---|---|---|---|
| Obwegeser third molar | right angled blade with a turned down tip, ring and loop handle | one size | 24 cm | 26 dollars |
| Obwegeser retractor 24 cm (this page) | right angled blade, bent up or bent down, ring and loop handle | seven blades, 5 x 16 to 16 x 80 mm | 24 cm | 26 dollars |
| Obwegeser soft tissue 21 cm | wider right angled blade, ring and loop handle | three blades, 11 x 40 to 16 x 80 mm | 21 cm | 26 dollars |
| Obwegeser ramus 24 cm | right angled blade with a notched tip, ring and loop handle | 11/15 x 70 or 12/22 x 70 mm | 24 cm | 26 dollars |
| Obwegeser ramus 22 cm | right angled blade with a notched tip, ring and loop handle | one size | 22 cm | 26 dollars |
| Obwegeser nasal spine 22 cm | narrow right angled blade, ring and loop handle | one size | 22 cm | 24 dollars |
| Obwegeser nasal spine 24 cm | right angled blade with a forked tip, ring and loop handle | one size | 24 cm | 24 dollars |
| Obwegeser chin | flat angled bar with a pronged tip | one size | 16 cm | 20 dollars |
| Obwegeser channel | flat bar, slim rounded end and a curved channel hook | 8 or 10 mm | 16 cm | 14 dollars |
| Munro ramus | broad curved blade on a solid hooked handle | four blades, 20 to 35 x 80 mm | 16 cm | 28 dollars |
Materials and finish
Every Obwegeser retractor we make is formed from high quality medical grade stainless steel. The steel itself is made to a German specification. We do not publish a grade number.
The finish is plain steel. Blade, shaft, ring and handle are one piece, so there is no joint at the bend. The blade size is part of the variation you order, so mark each size on the tray if you keep several.
Caring for it
Rinse it as soon as the case ends, before blood dries under the turned tip. Brush both faces of the blade, the inside of the bend and the inside of the loop handle. Dry it, steam sterilize it on the normal instrument cycle, and look at the tip before it goes back on the tray. A tip that has been bent flatter will not hook the flap, so set it aside rather than bend it back by hand.
Ordering and wholesale
The Obwegeser retractor is made by Adas Instruments in our own workshop and sold direct, which is why the price sits where it does against the catalog houses. Order one for a single tray, or in quantity for a hospital list or a distributor line. We do OEM work under your own brand and your own item numbers. Send us a sample and we will hold a run to your pattern rather than ours. Stock items ship from our own workshop. Backorder items take 10 to 12 working days to make. Every instrument carries a three year replacement warranty against manufacturing defects. Production is controlled under an ISO 13485 quality management system.
Frequently asked questions
What is an Obwegeser retractor used for?
The obwegeser soft tissue retractor 24cm holds the cheek, the lip, the muscle and the soft tissue flap off the jaw bones during surgery done through the mouth. The cases are the sagittal split of the lower jaw, Le Fort osteotomies of the upper jaw, genioplasty and the plating of jaw fractures. The bent tip hooks under the flap or round a bone border so the blade does not slide.
Should I order the Obwegeser retractor curved up or curved down?
The AI Mode answer gives the tip curved down a broader view and a firmer hold, and the tip curved up a gentler touch on the tissue held. A team can keep both in the sizes it uses. On our listing every blade is offered both ways at the same 26 dollars.
Which Obwegeser retractor blade size do I need?
Small blades, 5 x 16 and 7 x 25 mm, suit the front of the jaw and the chin. The 10 x 35 and 10 x 42 mm blades cover the premolar area, 12 x 55 and 14 x 70 mm the molars and the body, and 16 x 80 mm the ramus. The table on this page lists all seven.
How is the Obwegeser different from a Langenbeck retractor?
Both are hand held retractors with a blade at a right angle to the shaft. The Obwegeser is made for the jaw, long enough at 24 cm to reach the back of the mouth, and sold with its tip bent up or down. We list the Obwegeser range in this family table.
Can the Obwegeser retractor be autoclaved?
Yes. It is one piece of stainless steel with no joint, screw or coating, and it goes through the normal steam cycle with the rest of the tray. Rinse it and brush under the bent tip and inside the loop handle first, and dry it before it is packed.
Related products and categories
Three more jaw retractors from the same family: the Obwegeser soft tissue retractor, 21 cm, the Obwegeser ramus retractor, 24 cm and the Obwegeser ramus retractor, 22 cm. The rest of the range is under maxillofacial instruments, which sits inside our ENT instruments.



Reviews
There are no reviews yet.