What an Obwegeser ramus retractor is
The ramus rises from the angle of the jaw to the joint, and most of the cuts in jaw surgery cross it. The soft tissue over it has to be held back from the bone, and the retractor has to stay on a narrow, wet bone edge. The ramus retractor is the blade made to sit there.
Google AI Mode, read on 3 November 2026, describes the Obwegeser ramus retractor as an oral and maxillofacial instrument for moving the soft tissue without harm and exposing the bone along the ascending ramus. It names the sagittal split ramus osteotomy, orthognathic surgery and condylar neck procedures. It describes a curved distal blade that seats over the posterior border of the ramus and a notched or forked edge for a steady hold on the bone. Its answer lists our own 22 cm version at about 26 dollars.
Buyers ask for a ramus retractor, a mandibular retractor or a mandibular ramus retractor and mean this kind of blade. Gemini gives the Obwegeser mandibular retractor as another catalog name. The obwegeser ramus retractor uses below follow the cases the AI answer names.
Key design features
A notched tip
In our photograph the blade carries a notch at its tip and turns down. The notch fits over the bone edge and keeps the blade from sliding along it, so the assistant does not have to press hard to hold it in place. A light hold is easier to keep steady through a long split than a hard one, and it keeps the pressure on the soft tissue low while the cut is made.
A blade at a right angle
The blade is turned at a right angle to the shaft. The shaft runs back along the cheek while the blade drops onto the ramus, and the pull comes toward the front of the mouth, where the assistant stands.
Twenty two centimeters
At 22 cm it is the shorter of our two Obwegeser ramus retractors. It reaches the ramus from the corner of the mouth with the hand just outside the lips, which gives a closer, steadier hold than the 24 cm for a smaller patient. Keep one of each length on a split tray if the team operates on adults and on younger patients in the same list.
A ring and a loop
A ring sits on the shaft above an open loop handle. The loop takes the whole hand for a long pull, and a finger through the ring gives a lighter hold while the blade is being placed.
Which one to order
The listing carries one size, read on 3 November 2026. For a choice of two blades and a longer reach, see the 24 cm Obwegeser ramus retractor. A sagittal split is done on both sides of the jaw, so a pair lets the assistant move from one side to the other without cleaning the blade between them.
| What you get | Length | Working end | Price |
|---|---|---|---|
| Obwegeser ramus retractor | 22 cm | Right angled blade, notched tip | 26 dollars |
| A pair, one for each side | 22 cm | The same | 26 dollars each |
Where it is used
Gemini, read on 3 November 2026, places the 22 cm ramus retractor in oral and maxillofacial and facial trauma surgery, on the ramus, the sling of muscle that wraps it and the notch beside the coronoid.
| Case | What it holds | Why this blade |
|---|---|---|
| Sagittal split ramus osteotomy | Soft tissue off the ramus | The notch sits on the bone edge |
| Condylar neck surgery | Soft tissue at the upper ramus | The blade reaches the neck of the condyle |
| Ramus fracture | Tissue at the fracture line | A steady hold while the plate goes in |
| Removal of a lesion in the ramus | The flap over the bone | One hand holds, one is free |
What it holds back, and what it must not do
It holds tissue off the ramus. It is not a cheek retractor and it is not a lever.
| Job | Use the 22 cm ramus retractor? | What to use instead or beside it |
|---|---|---|
| Holding tissue off the ramus | Yes | This is the job it is made for |
| A wider or deeper hold | Beside it | The 24 cm ramus retractor, 12/22 x 70 mm |
| Sitting on the lower border during a split | No | An Obwegeser channel retractor |
| Holding the cheek and lip | No | An Obwegeser soft tissue retractor |
| Levering bone | Never | An elevator |
How it compares with the rest of the family
Ten Obwegeser and Munro jaw retractors make up this family on our site. The working ends are read off each listing’s own photograph, the sizes off the variations, the lengths off the name and the prices off the order form, on 3 November 2026.
| Retractor | Working end, from our photograph | Sizes on the listing | Length | Price |
|---|---|---|---|---|
| Obwegeser third molar | right angled blade with a turned down tip, ring and loop handle | one size | 24 cm | 26 dollars |
| Obwegeser retractor 24 cm | right angled blade, bent up or bent down, ring and loop handle | seven blades, 5 x 16 to 16 x 80 mm | 24 cm | 26 dollars |
| Obwegeser soft tissue 21 cm | wider right angled blade, ring and loop handle | three blades, 11 x 40 to 16 x 80 mm | 21 cm | 26 dollars |
| Obwegeser ramus 24 cm | right angled blade with a notched tip, ring and loop handle | 11/15 x 70 or 12/22 x 70 mm | 24 cm | 26 dollars |
| Obwegeser ramus 22 cm (this page) | right angled blade with a notched tip, ring and loop handle | one size | 22 cm | 26 dollars |
| Obwegeser nasal spine 22 cm | narrow right angled blade, ring and loop handle | one size | 22 cm | 24 dollars |
| Obwegeser nasal spine 24 cm | right angled blade with a forked tip, ring and loop handle | one size | 24 cm | 24 dollars |
| Obwegeser chin | flat angled bar with a pronged tip | one size | 16 cm | 20 dollars |
| Obwegeser channel | flat bar, slim rounded end and a curved channel hook | 8 or 10 mm | 16 cm | 14 dollars |
| Munro ramus | broad curved blade on a solid hooked handle | four blades, 20 to 35 x 80 mm | 16 cm | 28 dollars |
Materials and finish
Every Obwegeser ramus retractor we make is formed from high quality medical grade stainless steel. The steel itself is made to a German specification. We do not publish a grade number.
The finish is plain steel. Blade, shaft, ring and handle are one piece, with no joint at the bend. The notch meets bone in every case, so its edges are the first thing to look at before the tray is packed.
Caring for it
Rinse it as soon as the case ends, while bone dust is still wet in the notch. Brush the notch from both sides, both faces of the blade and the inside of the loop handle. Dry it, steam sterilize it on the normal instrument cycle, and look at the notch before it goes back on the tray. Set aside one with a bent notch rather than bend it back by hand.
Ordering and wholesale
The Obwegeser ramus retractor is made by Adas Instruments in our own workshop and sold direct, which is why the price sits where it does against the catalog houses. Order one for a single tray, or in quantity for a hospital list or a distributor line. We do OEM work under your own brand and your own item numbers. Send us a sample and we will hold a run to your pattern rather than ours. Stock items ship from our own workshop. Backorder items take 10 to 12 working days to make. Every instrument carries a three year replacement warranty against manufacturing defects. Production is controlled under an ISO 13485 quality management system.
Frequently asked questions
What is an Obwegeser ramus retractor used for?
It holds the soft tissue back and exposes the bone of the ascending ramus during sagittal split ramus osteotomies, condylar neck surgery, ramus fractures and other jaw surgery. The notched tip sits on the bone edge so the blade stays where the assistant places it while the saw works.
What are the uses of a ramus retractor?
The AI Mode answer names the sagittal split ramus osteotomy, orthognathic surgery and condylar neck procedures. In each one the job is the same: hold the soft tissue clear of the bone along the ramus so the surgeon can see the cut and the saw stays on bone.
Is a mandibular retractor the same as a ramus retractor?
Mandibular retractor is the wider name for any retractor used on the lower jaw. The ramus retractor is the one shaped for the upright back part of it. Gemini gives the Obwegeser mandibular retractor as another catalog name for this pattern.
Should I order the 22 cm or the 24 cm ramus retractor?
The 22 cm is one size and gives a closer hold for a smaller patient. The 24 cm reaches further and comes in two blades, 11/15 and 12/22 x 70 mm. Both are 26 dollars and both have the notched tip in our photographs.
Can it be autoclaved?
Yes. It is one piece of stainless steel with no joint, screw or coating, and it goes through the normal steam cycle with the rest of the tray. Rinse it and brush the notch first, and dry it before it is packed.
Related products and categories
Three more jaw retractors from the same family: the Obwegeser nasal spine retractor, 22 cm, the Obwegeser nasal spine retractor, 24 cm and the Obwegeser chin retractor. The rest of the range is under maxillofacial instruments, which sits inside our ENT instruments.



Reviews
There are no reviews yet.