What the Tessier retromaxillary lever is
The Tessier retromaxillary lever works where nothing else on the tray reaches: behind the upper jaw. Its shank turns a sharp corner and ends in a short upright blade, so the blade can be slipped round the back of the maxilla, behind the last molar, and set against the bone there. A pull on the large handle then levers the maxilla forward and down, after the cuts have freed it everywhere else.
Google AI Mode, read on 5 November 2026, describes the Tessier retromaxillary lever, listed in some catalogs as a maxillary mobilizer, as a reusable bone lever and elevator used in maxillofacial and craniofacial surgery. In its words, it is made for the controlled manipulation, mobilization and down fracture of the maxilla, above all in Le Fort osteotomies done to correct craniofacial deformity, jaw misalignment or midface trauma. After the bone cuts, it goes in behind the maxilla near the maxillary tuberosity and the pterygoid plates, and leveraged force loosens, advances or repositions the midface. It is made in left and right patterns, at about 15 cm.
Gemini, read the same day, places it in craniofacial, oral and maxillofacial and reconstructive plastic surgery, on the space behind the maxilla, the pterygoid plates and the bones at the back of the midface. It lists the Tessier retromaxillary elevator as a catalog name, and sets it apart from the Obwegeser mobilizer: a compact 15 cm lever with an angled head for behind the tuberosity, where the Obwegeser is 23 cm with a curved end.
Operating room teams name it the Tessier mobilizer or the Tessier maxillary mobilizer as readily as the retromaxillary lever, and all three mean this right angled instrument. It is used in pairs, one for each side of the jaw, after the front and side cuts and before the maxilla is moved to its planned position and fixed with plates. The lever does the moving; the plates do the holding.
Key design features
A serrated upright end
Our photograph and its drawings show a short upright end, cross serrated on its face. The serrations bite on the bone behind the maxilla and stop the end sliding off as the pull comes on. A smooth end would skid on wet bone at the moment the force is greatest, and a skid behind the maxilla lands in soft tissue the surgeon cannot see.
A right angled shank
The shank runs out from the handle and turns a right angle before the end. That corner is what takes the end round behind the maxilla while the shank lies along the teeth and the handle stays outside the mouth. The pull on the handle becomes a push from behind on the bone, which is the one direction the front cuts cannot supply.
Right, left or the pair
The drawings show a right and a left end, each turned toward its side. The listing sells each at 32 dollars or the two together at 60. A Le Fort case frees both sides of the maxilla, so the pair is the set to keep on the tray, and a single lever is the replacement when one is lost or worn.
A large hollow handle
The handle in our photograph is large and hollow, shaped to the palm. It spreads the force of a hard, steady pull across the hand. As the Tessier retromaxillary elevator, the instrument is all about that pull, and a thin handle would cut into the fingers. The hollow shape keeps the weight down, so the lever sits balanced in the hand rather than tipping toward the shank.
Which to order
Three options, read off the variations on 5 November 2026. The guide in the second column is ours.
| Option | Suits, our guide | Price |
|---|---|---|
| Set of 2 | A Le Fort tray, both sides of the maxilla | 60 dollars |
| Right | A replacement, or work on the right side only | 32 dollars |
| Left | A replacement, or work on the left side only | 32 dollars |
Where it is used
AI Mode and Gemini, read on 5 November 2026, name these cases for the Tessier retromaxillary lever. The reasons in the last column are ours, read off the end, the shank and the handle.
| Case | What it levers | Why this one |
|---|---|---|
| Le Fort osteotomy | The maxilla, from behind the tuberosity | Right angled shank reaches round |
| Craniofacial deformity correction | The midface, forward | Named by AI Mode |
| Midface trauma | A displaced maxilla | Named by AI Mode |
| Reconstructive plastic surgery | The back of the midface | Named by Gemini |
What it does, and what it must not do
The Tessier retromaxillary lever levers a maxilla that has already been cut free at the front and sides. It does not cut bone. Pull steadily on both sides in turn, so the maxilla comes forward evenly.
| Job | Use the Tessier lever? | What to use instead or beside it |
|---|---|---|
| Levering the maxilla from behind the tuberosity | Yes | This is the job it is made for |
| A longer curved lever for the down fracture | Beside it | The Obwegeser maxilla mobilizer |
| Making the bone cut | No | A saw, a bur or an osteotome |
| Splitting the lower jaw | No | The Smith sagittal split separator |
| Levering teeth | Never | An elevator |
How it compares with the rest of the orthognathic tray
Five orthognathic instruments make up this family on our site. The working ends and handles are read off each listing’s own photograph, the options off the variations and the prices off the order form, on 5 November 2026.
| Instrument | Working end, from our photograph | Handle, from our photograph | Size or options | Price |
|---|---|---|---|---|
| Smith ramus separator | two long flat narrow blades | long handles with a spring between them | with or without a ratchet | 55 dollars |
| Smith sagittal split separator | small flat angled blade on a curved shank | hollow fluted handle | right or left | 34 dollars |
| Obwegeser mobilizer | flat end bent into a curve | straight flat bar | 23 cm | 24 dollars |
| Tessier lever (this page) | short upright end, cross serrated, on a right angled shank | large hollow handle | 15 cm, right, left or a set of 2 | 32 or 60 dollars |
| Lindemann bur | spiral fluted cutting head tapering to a point | long smooth shank for the handpiece | 35, 22 or 10 mm | 12 dollars |
Materials and finish
Every Tessier retromaxillary lever we make is formed from high quality medical grade stainless steel. The steel itself is made to a German specification. We do not publish a grade number.
The Tessier retromaxillary lever has a plain steel finish. Look at the serrations and the corner of the shank before each case. Serrations worn smooth let the end skid, and a corner opened by a hard pull no longer reaches round, so that lever should be set aside.
Caring for it
Rinse the Tessier retromaxillary lever as soon as the case ends, before blood and bone dust dry in the serrations and inside the hollow handle. Brush them, wash it, dry it, and steam sterilize it on the normal cycle. Keep the right and the left together.
Ordering and wholesale
The Tessier retromaxillary lever is made by Adas Instruments in our own workshop and sold direct, which is why the price sits where it does against the catalog houses. Order one for a single tray, or in quantity for a hospital list or a distributor line. We do OEM work under your own brand and your own item numbers. Send us a sample and we will hold a run to your pattern rather than ours. Stock items ship from our own workshop. Backorder items take 10 to 12 working days to make. Every instrument carries a three year replacement warranty against manufacturing defects. Production is controlled under an ISO 13485 quality management system.
Frequently asked questions
What is the Tessier retromaxillary lever used for?
It mobilizes and down fractures the maxilla in Le Fort osteotomies, placed behind the maxilla near the maxillary tuberosity and the pterygoid plates, in AI Mode’s words. Ours is 15 cm, at 32 dollars each or 60 for the pair.
Should I order one Tessier lever or the set of 2?
Take the set of 2 for a Le Fort tray, because the maxilla is levered from both sides and each end turns toward its own side. Take a single right or left as a replacement. The pair is 60 dollars, a single 32.
Is a Tessier maxillary mobilizer the same instrument?
Yes. AI Mode says some catalogs list the Tessier retromaxillary lever as a maxillary mobilizer, and Gemini lists the Tessier retromaxillary elevator. Each name describes the same short right angled lever for behind the maxilla.
How is it different from the Obwegeser mobilizer?
The Tessier is 15 cm, with a short serrated end on a right angled shank, in right and left patterns. The Obwegeser is 23 cm, a flat bar with a curved end. Both lever the maxilla from behind.
Can it be autoclaved?
Yes. It is stainless steel with no coating, and it goes through the normal steam cycle with the rest of the tray. Brush the serrations and the inside of the hollow handle first, then dry it fully before it is wrapped.
Related products and categories
Three more instruments from the same orthognathic tray: the Lindemann bur, the Smith ramus separator and the Smith sagittal split separator. The rest of the range is under maxillofacial instruments, which sits inside our ENT instruments.


Reviews
There are no reviews yet.