What the Obwegeser alveolar osteotome is
The Obwegeser alveolar osteotome has the narrowest blade of the alveolar cutters on our site. Its 2 mm blade is narrow enough to work between two roots that almost touch, and it is made in one piece, so the shaft is the handle. That keeps it light in the fingers for the small, careful cuts that free a segment of teeth or open the crest of a narrow ridge.
Google AI Mode, read on 4 November 2026, describes the Obwegeser alveolar osteotome as an instrument used in oral and maxillofacial surgery to cut, reshape or divide the alveolar bone of the upper and lower jaws. It adds dental, ENT and plastic surgery, and describes a double beveled edge and a ridged grip for mallet work. It gives 3, 4 and 6.5 mm as widths; ours are 2, 4 and 6.5 mm.
Gemini, read the same day, places it in oral and maxillofacial surgery and dental implant work, on alveolar ridges, block grafts of bone and the bone under the gum. It lists the mini alveolar osteotome and the obwegeser alveolar osteotome 2mm 4mm 6.5mm as catalog names. Buyers type the plain alveolar osteotome, or bone graft osteotome.
Key design features
A very narrow blade
Our photograph shows a very narrow blade at the tip, and the drawings beside it show two tips. At 2 mm the smallest blade fits between roots that sit close together. Gemini calls it a mini alveolar osteotome for that reason.
One piece, ridged along its length
The osteotome is one slim piece of steel, ridged along the length of the shaft. There is no separate handle. The fingers hold the ridged shaft itself, close to the work, which gives a fine feel for each light blow. A light instrument also tires the hand less over a long segmental case, where dozens of small cuts are made one after another.
Three widths
The listing sells 2, 4 and 6.5 mm, all at 19 dollars. The 2 mm works between close roots. The 4 mm cuts round a single tooth, and the 6.5 mm opens the crest of a ridge or shapes a small block graft. All three can sit on one tray, so the width changes with the bone without the surgeon leaving the cut.
Two Obwegeser alveolar listings
Our site carries two Obwegeser alveolar osteotomes. This one, ADM-620.02, is one piece, in 2, 4 and 6.5 mm at 19 dollars. The Obwegeser osteotome for the alveolar process, ADM-684.03, has a separate ridged handle and comes in 3, 4 and 6.5 mm.
Which width to order
Three widths at one price, read off the variations on 4 November 2026. The guide below is ours. The listing gives no length.
| Width | Suits, our guide | Price |
|---|---|---|
| 2 mm | Between roots that sit close together | 19 dollars |
| 4 mm | Cuts round a single tooth | 19 dollars |
| 6.5 mm | Opening a ridge, or shaping a small block graft | 19 dollars |
Where it is used
AI Mode and Gemini, read on 4 November 2026, name these cases for the Obwegeser alveolar osteotome.
| Case | What it cuts | Why this one |
|---|---|---|
| Segmental jaw surgery | Alveolar bone between the teeth | The 2 mm fits between close roots |
| Crest expansion before an implant | The crest of a narrow ridge | Gemini names it |
| Block bone grafts | A small graft of bone | The 6.5 mm shapes it |
| Dental, ENT and plastic surgery | Alveolar bone of both jaws | Named by AI Mode |
What it does, and what it must not do
The Obwegeser alveolar osteotome makes fine cuts in the bone round the teeth. It is not for the thick bone of the ramus and not a lever.
| Job | Use the alveolar osteotome? | What to use instead or beside it |
|---|---|---|
| Fine cuts in the alveolar bone | Yes | This is the job it is made for |
| A 3 mm cut with a separate ridged handle | Beside it | The Obwegeser osteotome for the alveolar process |
| Splitting the ramus | No | The Hargis osteotome |
| Long straight cuts across the jaw | No | The Obwegeser blade osteotome |
| Levering a tooth or a segment | Never | Nothing; the blade is not a lever |
How it compares with the rest of the osteotomes
Eleven maxillofacial osteotomes make up this family on our site. The working ends and handles are read off each listing’s own photograph, the options off the variations and the prices off the order form, on 4 November 2026. No listing gives a length, so none is printed.
| Osteotome | Working end, from our photograph | Handle, from our photograph | Options on the listing | Price |
|---|---|---|---|---|
| Dautrey-Munro | broad flat blade running the full length of a one piece bar | the bar itself, to a small flared striking end | 4, 6, 8, 10, 12, 14 or 16 mm | 22 dollars |
| Epker | long slim blade; drawings of straight, slightly and strongly curved tips | knurled lower grip, round flared striking end | 4, 6 or 8 mm by 1.2 mm, three curves | 20 dollars |
| Hargis | short, broad flat blade on a narrow neck | dark textured handle | 10 or 20 mm | 36 dollars |
| Obwegeser blade | flat blade on a narrow neck; drawings of four widths | brown handle with a metal end cap | 8, 12, 16 or 20 mm | 36 dollars |
| Obwegeser wedge | narrow flat blade on a neck; a thin tapered wedge in the drawing | brown handle with a metal end cap | 7 or 10 mm | 37 dollars |
| Obwegeser maxillary | one piece flat bar curving toward its tip | the bar itself, to a flared striking end | 8 or 11 mm | 28 dollars |
| Obwegeser nasal septum | forked tip, two prongs ending in small round knobs | long slim shaft to a square striking block | 4 or 6 mm | 33 dollars |
| Obwegeser alveolar process | narrow blade at the tip of a slim shaft | ridged handle | 3, 4 or 6.5 mm | 20 dollars |
| Obwegeser alveolar, one piece (this page) | very narrow blade on a slim one piece shaft | the shaft, ridged along its length | 2, 4 or 6.5 mm | 19 dollars |
| Marchac | slim straight blade; drawings of three widths | ridged handle with a round striking cap | 4, 6 or 8 mm, straight or curved | 23 dollars |
| Tessier graft calva | broad flat blade; square shoulders in the drawing | faceted shaft to a round flared striking plate | 10 or 15 mm, straight or curved | 33 dollars |
Materials and finish
Every Obwegeser alveolar osteotome we make is formed from high quality medical grade stainless steel. The steel itself is made to a German specification. We do not publish a grade number.
The Obwegeser alveolar osteotome has a plain steel finish. Look along the narrow edge before each case. A chipped edge on a 2 mm blade wanders in the bone, and that osteotome should be set aside.
Caring for it
Rinse the Obwegeser alveolar osteotome as soon as the case ends, before blood and bone dust dry on the blade and in the ridges of the shaft. Brush both, wash it, dry it, and steam sterilize it on the normal cycle. Keep the three widths in order on the tray.
Ordering and wholesale
The Obwegeser alveolar osteotome is made by Adas Instruments in our own workshop and sold direct, which is why the price sits where it does against the catalog houses. Order one for a single tray, or in quantity for a hospital list or a distributor line. We do OEM work under your own brand and your own item numbers. Send us a sample and we will hold a run to your pattern rather than ours. Stock items ship from our own workshop. Backorder items take 10 to 12 working days to make. Every instrument carries a three year replacement warranty against manufacturing defects. Production is controlled under an ISO 13485 quality management system.
Frequently asked questions
What is the Obwegeser alveolar osteotome used for?
It cuts, reshapes or divides the alveolar bone of the upper and lower jaws in oral and maxillofacial surgery, in AI Mode’s words. Gemini adds implant work and block grafts. Ours is a one piece shaft in 2, 4 or 6.5 mm, at 19 dollars.
Which alveolar osteotome width should I order?
The 2 mm works between roots that sit close together, and the 4 mm round a single tooth. The 6.5 mm opens the crest of a ridge or shapes a small block graft. All three are 19 dollars.
How is this alveolar osteotome different from the other one?
Our site carries two. This one, ADM-620.02, is one piece, in 2, 4 and 6.5 mm at 19 dollars. The other, ADM-684.03, has a separate ridged handle, in 3, 4 and 6.5 mm at 20 dollars.
Is a mini alveolar osteotome the same instrument?
Gemini lists the mini alveolar osteotome as a catalog name for this pattern, for the fine 2 mm edge. Mini describes the size of the blade, made for small cuts before an implant or a crest expansion.
Can it be autoclaved?
Yes. It is stainless steel with no coating, and it goes through the normal steam cycle with the rest of the tray. Brush the ridges of the shaft clean, dry it fully, and store it so the narrow edge is protected.
Related products and categories
Three more osteotomes from the same maxillofacial tray: the Marchac osteotome, the Tessier graft calva osteotome and the Dautrey-Munro osteotome. The rest of the range is under maxillofacial instruments, which sits inside our ENT instruments.



Reviews
There are no reviews yet.