What the Hargis osteotome is
The Hargis osteotome is a splitter. Once the cuts for a sagittal split have been made through the outer plate of the lower jaw, the two halves of the ramus still have to be parted along their length, through the bone that holds them together. A broad blade that thickens from its edge back is driven into the line, and as it goes in, the taper wedges the halves apart.
Google AI Mode, read on 4 November 2026, describes the Hargis osteotome as an oral and maxillofacial instrument used in orthognathic surgery, skull reconstruction and complex cleft and trauma cases. It describes two Hargis patterns. The sagittal splitting osteotome is a bone splitter for the bilateral sagittal split osteotomy, with a graduated taper that follows a line down the ramus. The pterygoid osteotome is curved, for the back of the upper jaw. Our photograph shows a straight, broad blade, so ours is the splitting pattern.
Gemini, read the same day, places it in oral and maxillofacial, orthognathic and facial reconstructive surgery, on the body of the lower jaw, the planes of a ramus osteotomy and thick cortical bone. It lists the Hargis sagittal split osteotome, the Hargis bone osteotome and the hargis osteotome 10mm 20mm as catalog names. Buyers who start wider type bone splitter.
Key design features
A short, broad blade
Our photograph shows a short, broad flat blade on a narrow neck. The breadth spreads the force of each blow along the line of the split. The short blade stays stiff under the mallet, where a long thin one would flex. Stiffness matters here, because a splitting blow that bends the blade loses its force before it reaches the bone it is meant to part.
A tapered side profile
The drawing beside the instrument shows the blade from the side, thin at the edge and thickening back toward the neck. That taper is what makes it a splitter. The edge enters the line, and the thicker part behind it opens the halves as the blade is driven on.
Two widths
The listing sells the Hargis in 10 and 20 mm, both at 36 dollars. The 10 mm suits the narrower bone near the top of the ramus. The 20 mm spreads the split along the thicker body of the jaw, which Gemini names as its ground.
A textured handle
The handle in our photograph is dark and textured over its length. Splitting dense bone takes heavy blows, and a textured handle keeps the grip steady on a wet glove between them, while the hand holds the blade on its line.
Which width to order
Two widths at one price, read off the variations on 4 November 2026. The guide below is ours. The listing gives no length.
| Width | Suits, our guide | Price |
|---|---|---|
| 10 mm | The narrower bone near the top of the ramus | 36 dollars |
| 20 mm | The thicker bone along the body of the jaw | 36 dollars |
Where it is used
AI Mode and Gemini, read on 4 November 2026, name these cases for the Hargis osteotome.
| Case | What it splits | Why this one |
|---|---|---|
| Bilateral sagittal split osteotomy | The ramus, outer from inner plate | The taper wedges the halves apart |
| Orthognathic surgery of the lower jaw | Thick cortical bone of the body | The 20 mm spreads the force |
| Skull reconstruction | Bone that is divided along a line | Named by AI Mode |
| Cleft and trauma cases | Bone in complex repairs | The short blade stays stiff |
What it does, and what it must not do
The Hargis osteotome splits bone along a line that has already been cut. It is not the first cut, and it is not a lever.
| Job | Use the Hargis? | What to use instead or beside it |
|---|---|---|
| Splitting the ramus after the cuts are made | Yes | This is the job it is made for |
| Carrying a thin cut round the angle of the jaw | Beside it | The Epker osteotome |
| Separating the back of the upper jaw | Beside it | The Obwegeser maxillary osteotome |
| Making the first cut through the outer plate | No | A saw or a bur |
| Prying the halves apart by the handle | Never | A sagittal split separator |
How it compares with the rest of the osteotomes
Eleven maxillofacial osteotomes make up this family on our site. The working ends and handles are read off each listing’s own photograph, the options off the variations and the prices off the order form, on 4 November 2026. No listing gives a length, so none is printed.
| Osteotome | Working end, from our photograph | Handle, from our photograph | Options on the listing | Price |
|---|---|---|---|---|
| Dautrey-Munro | broad flat blade running the full length of a one piece bar | the bar itself, to a small flared striking end | 4, 6, 8, 10, 12, 14 or 16 mm | 22 dollars |
| Epker | long slim blade; drawings of straight, slightly and strongly curved tips | knurled lower grip, round flared striking end | 4, 6 or 8 mm by 1.2 mm, three curves | 20 dollars |
| Hargis (this page) | short, broad flat blade on a narrow neck | dark textured handle | 10 or 20 mm | 36 dollars |
| Obwegeser blade | flat blade on a narrow neck; drawings of four widths | brown handle with a metal end cap | 8, 12, 16 or 20 mm | 36 dollars |
| Obwegeser wedge | narrow flat blade on a neck; a thin tapered wedge in the drawing | brown handle with a metal end cap | 7 or 10 mm | 37 dollars |
| Obwegeser maxillary | one piece flat bar curving toward its tip | the bar itself, to a flared striking end | 8 or 11 mm | 28 dollars |
| Obwegeser nasal septum | forked tip, two prongs ending in small round knobs | long slim shaft to a square striking block | 4 or 6 mm | 33 dollars |
| Obwegeser alveolar process | narrow blade at the tip of a slim shaft | ridged handle | 3, 4 or 6.5 mm | 20 dollars |
| Obwegeser alveolar, one piece | very narrow blade on a slim one piece shaft | the shaft, ridged along its length | 2, 4 or 6.5 mm | 19 dollars |
| Marchac | slim straight blade; drawings of three widths | ridged handle with a round striking cap | 4, 6 or 8 mm, straight or curved | 23 dollars |
| Tessier graft calva | broad flat blade; square shoulders in the drawing | faceted shaft to a round flared striking plate | 10 or 15 mm, straight or curved | 33 dollars |
Materials and finish
Every Hargis osteotome we make is formed from high quality medical grade stainless steel. The steel itself is made to a German specification. We do not publish a grade number.
The Hargis osteotome has a plain steel finish. Look along the edge before each case. A splitting blade takes heavy blows, so check the neck as well: a neck that has bent will not drive the blade straight, and that osteotome should be set aside.
Caring for it
Rinse the Hargis osteotome as soon as the case ends, before blood and bone dust dry on the blade and the textured handle. Brush both, wash it, dry it, and steam sterilize it on the normal cycle with the rest of the tray.
Ordering and wholesale
The Hargis osteotome is made by Adas Instruments in our own workshop and sold direct, which is why the price sits where it does against the catalog houses. Order one for a single tray, or in quantity for a hospital list or a distributor line. We do OEM work under your own brand and your own item numbers. Send us a sample and we will hold a run to your pattern rather than ours. Stock items ship from our own workshop. Backorder items take 10 to 12 working days to make. Every instrument carries a three year replacement warranty against manufacturing defects. Production is controlled under an ISO 13485 quality management system.
Frequently asked questions
What is the Hargis osteotome used for?
AI Mode names orthognathic surgery, skull reconstruction and complex cleft and trauma cases. Its splitting pattern parts the ramus in a bilateral sagittal split osteotomy. Ours is that straight splitting pattern in 10 or 20 mm, at 36 dollars.
Which Hargis pattern is this, splitting or pterygoid?
AI Mode describes two Hargis patterns: a straight sagittal splitting osteotome and a curved pterygoid osteotome for the back of the upper jaw. Our photograph shows a straight, broad blade, so ours is the splitting pattern.
Which Hargis width should I order?
The 10 mm suits the narrower bone near the top of the ramus. The 20 mm spreads the split along the thicker body of the lower jaw. Both are 36 dollars, and a sagittal split tray can carry the pair, so the width follows the bone from the ramus to the body.
What is a bone splitter?
A bone splitter is a broad osteotome with a taper behind its edge. Driven into a line that has already been cut, the taper wedges the two sides of the bone apart. AI Mode uses the phrase for the Hargis splitting pattern.
Can it be autoclaved?
Yes. It is stainless steel with no coating, and it goes through the normal steam cycle with the rest of the tray. Brush the textured handle clean, dry it fully, and store it so the edge is protected.
Related products and categories
Three more osteotomes from the same maxillofacial tray: the Obwegeser blade osteotome, the Obwegeser wedge osteotome and the Obwegeser maxillary osteotome. The rest of the range is under maxillofacial instruments, which sits inside our ENT instruments.


Reviews
There are no reviews yet.