What an Obwegeser channel retractor is
In a sagittal split of the lower jaw, the last cut runs down through the lower border of the bone. On the far side of that border lie the soft tissue, the facial vessels and the nerve. A flat retractor pressed against them can slip; a blade with a channel can sit on the bone edge itself and hold them to one side.
Google AI Mode, read on 3 November 2026, describes the Obwegeser channel retractor as an oral and maxillofacial instrument used to hold soft tissue and the structures beside the bone clear during osteotomies of the mandible. It describes raised edges that form a shallow trough, so the blade straddles or hooks round the inferior border of the jaw, and it places it in the bilateral sagittal split osteotomy. It gives lengths of 16 to 22 cm and names 8 mm and 10 mm widths, which are our two variations at 16 cm.
Buyers also ask for a channel retractor, an obwegeser mandibular channel retractor, which is Gemini’s name for it, or an inferior border retractor, after the edge it sits on. The channel retractor uses below follow the cases both AI answers name.
Key design features
A channel shaped hook
In our photograph one end of the bar curves round into a hook with a channel in it. The channel fits over the lower border of the jaw, so the blade sits on the bone rather than resting on soft tissue, and it stays there while the cut is made.
Two widths
The listing carries an 8 mm and a 10 mm width. The AI Mode answer gives the narrower one to confined spaces and the wider one to a broader zone in an adult jaw. A tray for splits on both sides can carry one of each, at 14 dollars apiece.
A slim rounded end
The opposite end of the bar is slim with a small rounded tip. In our photograph it is the end the hand holds, and its rounded tip leaves nothing sharp near the lip while the channel end works at the back of the jaw.
Sixteen centimeters, one flat piece
At 16 cm it is short and stiff, which is what a blade on a bone edge needs. It is one flat piece with no joint and no loop, so nothing can flex or turn between the hand and the channel. A longer, springier blade would move as the saw meets the bone; this one holds its place.
Which width to order
The two variations on the listing, read on 3 November 2026. Both are 16 cm and both cost the same.
| Width on the listing | Length | Where it suits | Price |
|---|---|---|---|
| 8 mm | 16 cm | A confined space or a smaller jaw | 14 dollars |
| 10 mm | 16 cm | A broader hold on an adult jaw | 14 dollars |
Where it is used
Gemini, read on 3 November 2026, places it in oral and maxillofacial and orthognathic surgery, on the inferior and posterior border of the mandibular ramus during the sagittal split osteotomy.
| Case | Where the channel sits | What it holds aside |
|---|---|---|
| Bilateral sagittal split osteotomy | The lower border of the jaw | Soft tissue, vessels and nerve beside the bone |
| Lower border cut in jaw surgery | The lower border | Soft tissue below the jaw |
| Plating near the lower border | Beside the plate | The soft tissue over the border |
| Removal of bone at the angle | The border at the angle | Soft tissue round the angle |
What it holds back, and what it must not do
It holds soft tissue at the bone edge. It is not a cheek retractor, and it does not separate the split.
| Job | Use the channel retractor? | What to use instead or beside it |
|---|---|---|
| Sitting on the lower border during a split | Yes | This is the job it is made for |
| Holding tissue off the ramus | Beside it | An Obwegeser ramus retractor |
| Separating the two halves of the split | No | A sagittal split separator |
| Holding the cheek and lip | No | An Obwegeser soft tissue retractor |
| Levering bone | Never | An elevator |
How it compares with the rest of the family
Ten Obwegeser and Munro jaw retractors make up this family on our site. The working ends are read off each listing’s own photograph, the sizes off the variations, the lengths off the name and the prices off the order form, on 3 November 2026.
| Retractor | Working end, from our photograph | Sizes on the listing | Length | Price |
|---|---|---|---|---|
| Obwegeser third molar | right angled blade with a turned down tip, ring and loop handle | one size | 24 cm | 26 dollars |
| Obwegeser retractor 24 cm | right angled blade, bent up or bent down, ring and loop handle | seven blades, 5 x 16 to 16 x 80 mm | 24 cm | 26 dollars |
| Obwegeser soft tissue 21 cm | wider right angled blade, ring and loop handle | three blades, 11 x 40 to 16 x 80 mm | 21 cm | 26 dollars |
| Obwegeser ramus 24 cm | right angled blade with a notched tip, ring and loop handle | 11/15 x 70 or 12/22 x 70 mm | 24 cm | 26 dollars |
| Obwegeser ramus 22 cm | right angled blade with a notched tip, ring and loop handle | one size | 22 cm | 26 dollars |
| Obwegeser nasal spine 22 cm | narrow right angled blade, ring and loop handle | one size | 22 cm | 24 dollars |
| Obwegeser nasal spine 24 cm | right angled blade with a forked tip, ring and loop handle | one size | 24 cm | 24 dollars |
| Obwegeser chin | flat angled bar with a pronged tip | one size | 16 cm | 20 dollars |
| Obwegeser channel (this page) | flat bar, slim rounded end and a curved channel hook | 8 or 10 mm | 16 cm | 14 dollars |
| Munro ramus | broad curved blade on a solid hooked handle | four blades, 20 to 35 x 80 mm | 16 cm | 28 dollars |
Materials and finish
Every Obwegeser channel retractor we make is formed from high quality medical grade stainless steel. The steel itself is made to a German specification. We do not publish a grade number.
The finish is plain steel. The whole retractor is one flat piece with no joint. The edges of the channel are the part that sits on bone, so look along them before each case.
Caring for it
Rinse it as soon as the case ends, while bone dust is still wet in the channel. Brush inside the channel and along both edges. Dry it, steam sterilize it on the normal instrument cycle, and look at the hook before it goes back on the tray. A channel that has been opened or squeezed will not sit on the border, so set it aside rather than bend it back by hand.
Ordering and wholesale
The Obwegeser channel retractor is made by Adas Instruments in our own workshop and sold direct, which is why the price sits where it does against the catalog houses. Order one for a single tray, or in quantity for a hospital list or a distributor line. We do OEM work under your own brand and your own item numbers. Send us a sample and we will hold a run to your pattern rather than ours. Stock items ship from our own workshop. Backorder items take 10 to 12 working days to make. Every instrument carries a three year replacement warranty against manufacturing defects. Production is controlled under an ISO 13485 quality management system.
Frequently asked questions
What is an Obwegeser channel retractor used for?
It sits on the lower border of the jaw and holds the soft tissue, the vessels and the nerve beside the bone to one side while the bone is cut. Its main use is the bilateral sagittal split osteotomy, and it is also used for other cuts and plating near the lower border of the mandible.
What are the uses of a channel retractor?
Both AI answers read on 3 November 2026 name the sagittal split osteotomy of the lower jaw first. In that case the channel sits on the lower border of the bone while the final cut is made. It also serves for other work at the lower border and the angle of the jaw.
Should I order the 8 mm or the 10 mm channel retractor?
The AI Mode answer gives the 8 mm to confined spaces close to the nerve and the 10 mm to a broader zone in an adult jaw. Both are 16 cm and 14 dollars. A split is done on both sides, so a tray can carry one of each width.
Is a channel retractor the same as an inferior border retractor?
The inferior border is the lower edge of the jaw, and the channel retractor is the one that sits on it, so the two names point to the same job. Gemini also gives the Obwegeser mandibular channel retractor and the Obwegeser sagittal split channel retractor.
Can it be autoclaved?
Yes. It is one piece of stainless steel with no joint, screw or coating, and it goes through the normal steam cycle with the rest of the tray. Rinse it and brush inside the channel first, and dry it before it is packed.
Related products and categories
Three more jaw retractors from the same family: the Munro ramus retractor, the Obwegeser third molar retractor and the Obwegeser retractor, 24 cm. The rest of the range is under maxillofacial instruments, which sits inside our ENT instruments.


Reviews
There are no reviews yet.